How to tie a spatula hook to line and braid: the best knots

When fishing, anglers often encounter line breaks and loss of hooks. And if any angler is not insured against cliffs, then only beginners can untie the knots. The ability to tie the hook correctly is essential for every fisherman. Special problems arise for inexperienced anglers when tying hooks with a shovel, since the simplest knots in a “loop” in this case do not fit. But with the knowledge of special knots, a hook with a spatula can be tied even more securely than with an eyelet, and this knot will look neater and more compact than on a hook with a hole for the fishing line.
Compact knot on the hook with a shovel [/ caption]

What is the strength of the blade in the structure?

Shod hooks with a shovel are not in vain popular among fishermen. This is due to the fact that they are considered to be more durable and reliable. Usually, the knot is less noticeable on them. When a fisherman uses small hooks, it is easier for him to use this design than to pull the line into the small eye. When tying such hooks, the knot should not have many kinks, as this reduces its strength. However, it cannot be too simple so as not to loosen and slip off. For hook knots without an eyelet, the use of friction is essential. The knots should be tied tightly and not slipping. When tying hooks without an ear, it is especially important to follow certain rules carefully. Usually, complex knots are used for this, in the technique of which it is necessary not only to understand, but also to achieve automatism.Only well-mastered knots will provide high reliability of the connection.

How to tie a hook with a shovel

There are nodes, the reliability of which has been confirmed by many years of practice. To be sure of strength, you need to tie them neatly, without deviating from the rules. The following are options that are suitable for use with different types of line.

When fishing in cold weather, it must be borne in mind that the braid sometimes absorbs water and can freeze. Therefore, it is preferable to use it with a tight weave or take nylon line instead. You can use special anti-freeze sprays. Instead, you can use liquid petroleum jelly or a similar material.

Knots for small hook numbers

In this case, using a node called “python” is fine. To do this, do the following:

1. Around the forend, make 2 loops with a figure of eight, so that the center is on one side, and the edges on the other.
2. The tip is passed through both loops again and tightened.

In the figure you can see the details of the node creation:
Node-eight [/ caption]

Tie a hook with a spatula to a monofilament line

A generic node is often used. To use it, you need to do the following:

1. The tip of the line is placed vertically along the forend from bottom to top with a significant margin.
2. A small loop is made on the fold at the bottom.
3. The end of the line is wrapped around the shank of the hook and the tip of the line. In this case, it is enough to make 4-5 turns, moving up. The hinges should be parallel and close to each other.
4. The tip of the fishing line, which should look up, is threaded through the loop located below. The knot is moistened and tightened.

The following diagram shows in detail each stage of tying a knot:

How to tie a spatula hook to a fluorocarbon line

For fluorocarbon, the Snell knot is often used. It is known for its high strength. To apply it, you need to perform the following actions:

1. The line is placed along the forend of the hook with a significant margin. Make a large loop. It should be sized so that the hook passes freely through it.
2. They make turns with the tip, capturing the inside of the loop and the forend. The loops start at the top and continue down.
3. After the last turn, the tip of the fluor is threaded through the loop.
4. The assembly must be moistened and then tightened.

This image shows details of the knot tying process. It is used for hooks with a shoulder blade and for those that have an eyelet.

Knots on very thin and very thick line

For a thin line, you can use a bloody knot. It has such an unusual name due to what is rumored to be done on whips in this way when punishing sailors hundreds of years ago. To attach a hook to such a knot, do the following:

1. The end of the line is positioned along the forend of the hook.
2. Make a wide turn around him and the fishing line.
3. Another such turn is performed.
4. The running end is passed from top to bottom inside the second loop.
5. Tighten the knot.

This option is widely used. It is suitable for hooks with a shoulder blade, with an eyelet, and for creating a multi-hook tackle. Details of how to tie the knot correctly can be seen in the diagram.
Bloody knot [/ caption] To increase the strength of the bloody knot, you can make more than one additional loop, but several. In this case, the tip must be threaded through the inside of each of them. For thick fishing line, use the “deflection” knot. It is performed in this way:

1. The tip is folded in half.
2. Leaving a loop at the bottom, it is wrapped around the fishing line and forend, leaving the loops free. You need to make 5-6 turns.
3. The tip is passed inside the loops from top to bottom and threaded into the lower loop left in advance.
4. The knot is tightened.

This node also has a second name: the shell node. It is considered one of the most durable. It is considered relatively difficult, so you need to be especially careful about tying it. How to tie it correctly can be clarified in the following photo-diagram: We
tie a hook with a spatula – step-by-step video: https://youtu.be/4F7kAvPwUp8

Braided attachment

The best knot for a shovel hook is the so-called stepped knot. It has high reliability, but is relatively complex. It is done this way:

1. The tip of the fishing line is folded in half with a significant margin and placed along the forend of the hook.
2. It is wound around the forearm and one line several times, gradually dropping down.
3. Then they continue winding, but they already grab both parts of the fishing line. This is also done several times. It is necessary that there is a loop at the bottom.
4. The tip is threaded into it. It is recommended to wet the knot before tightening.

If you need to clarify how to tie it, just read the following photo:
Knot for the cord [/ caption]

Secrets and Tips

In such nodes, it is required to perform a large number of turns. They should be parallel and in close contact with each other. Overlaps are not allowed. If the tip of the line is too large, it must be cut off. It is enough to leave no more than 2-4 mm. Tightening should be done in such a way that their shape is not disturbed. If this does happen, it is better not to leave the knot, but to tie it up. It is recommended to wet before tightening. It allows you to tighten the knot more and thereby make it stronger. This procedure reduces friction when tightening. In some cases, it can seriously damage the line.
In order to use hooks with a shovel, there is no need to study a large number of knots, it is enough to master 3-4, but to work out their use to automatism.

Поделиться ссылкой: