Do-it-yourself winter fishing rod: how to make tackle for lure, for a balancer, making a self-cutting fishing rod and for fishing with mormyshka. Independent production of fish tackle will appeal to every angler. Sometimes it is difficult to find a suitable winter fishing rod, sometimes you need to save money, and sometimes you need to make a fishing rod from improvised materials. Then you can make a fishing rod for winter fishing on your own, which will 100% satisfy all your wishes. It is worth familiarizing yourself with how a winter fishing rod is made with your own hands in order to make a quality product.
Homemade winter fishing rods for lure: drawings and instructions for self-production
In order for the manufacture of a winter fishing rod for do-it-yourself fishing to be successful, you will need a little patience and tools. The following accessories will be required:
coil;
hollow whip of glass;
thin coal whip;
a couple of rings;
5 champagne corks;
2 paperclips.
From the carbon fiber whip, you need to saw off a piece of material 30 cm long, twist it with a thin tube. Next, you need to cut off the same number of centimeters from the coal whip. It will serve as a “knee”. After that, you should find corks from a champagne bottle, dry them, drill them and put them on the handle of the future fishing rod. So that they do not move out, it is advisable to attach them to each other, as well as to the main part of the product. Then the handles should be sanded. To do this, insert the second knee and whip, then take the plug and glue it securely. With the help of nail polish and thread, the edges of the knees should be strengthened, after which the rings should be glued. You can use paper clips. At the end, on the cork, you need to cut the place where the coil will be attached. After that, it is glued around the edges with glue, additionally wrapped with insulating tape.
Do-it-yourself winter electronic fishing rod: instruction with photo
It is quite possible to make electronic homemade winter fishing rods on your own. Such a homemade product allows you to automate the process of playing with a mormyshka as much as possible. To make an electronic fishing rod, you will need the following items:
electric toothbrush with working mechanism;
a little cold welding to secure the structural elements;
whip;
nod;
spool.
After preparing the necessary materials, you can begin to manufacture an electronic fishing rod. On one side of the toothbrush, you need to attach a spool pre-cut into 2 parts. It is recommended to make a small hole in it for convenience, reliability. On the opposite side, a small whip is glued into it. This is where cold welding comes in handy. You can buy it at a car shop, in the same place where spare parts are sold. Next, you need to wind the fishing line, attach the mormyshka. Homemade electronic oud runs on a single AA battery. When the motor is turned on, the whip starts to vibrate, the vibration is transmitted to the mormyshka.
Making a winter fishing rod for fishing on a float
It is quite easy to make your own float fishing rod. At the same time, it is worth considering the features of the type of fishing for which the tackle is made. For float fishing, a fishing rod is made, taking into account the fact that the work on the float goes to a fixed nozzle. The float can be made from foam. Winter float gear is done like this:
you need to cut a rectangular piece of foam with a size of 10 cm;
with a knife, a square fragment is turned into a cone;
with a file from sandpaper, the foam is cultivated;
a pin or wire in the form of a loop is inserted into the sharp part of the cone.
If desired, the float in the form of a cone can be decorated.
A simple do-it-yourself fishing rod: do-it-yourself “balalaika” from improvised means
Balalaika winter fishing rod can be made from improvised means. This will require the following materials:
a small piece of plastic 5 mm thick;
ruler or tape measure;
old coil;
stationery knife;
old antenna from the TV – you need a small piece of tube;
compass;
whip;
sandpaper;
glue.
First you need to measure the diameter of the coil, transfer it to the plastic. After that, the hole should be cut out, polished with a clerical knife or sandpaper. The edge of the hole must be re-machined. Then they apply the coil to the plastic and draw the future balalaika. According to the image, the extra pieces need to be cut off. The nose of the fishing rod is made from the remnants, where a hole for the tube will then be drilled. All parts must be carefully sanded, insert the coil into the hole.
It is important to pay attention to the location of the brake lever. In winter fishing, it is convenient to use a fishing rod with one hand. The second must remain free.
At the end, a hole is drilled for a tube from a television antenna. After that, it is glued, a whip is stuck into the tube. Fix it with glue.
Making a winter fishing rod-garland
This is a very interesting tackle that allows you to fish in several layers of the reservoir at once. You can determine at what depth the fish should be caught. When using a garland, the effectiveness of fishing is significantly increased. Often in winter, fish leave the bottom layer, sometimes they do not bite at all. This is because the fish move into the water column and move and feed without sinking to the bottom. In such situations, a garland should be used. It is advisable to knit gear without large knots, as they scare away fish. It is necessary to unwind the required amount of fishing line, thread it into the eye of the bait, wrap the tip around the fishing line over the bait 3 times and draw the end of the fishing line under the winding. Then, again thread it into the ear. The procedure is repeated, depending on the planned number of mormyshki, nozzles. They must be tied in sequence, with the exception of hooks. They are already attached to the knot.
Winter fishing rod filly: simple homemade
This is the simplest winter fishing rod, which is made of hard foam or other similar material. Previously, the filly’s body was carved from wood. Now it is better to use foam, it is easy to get and process. Plus, it’s lighter than wood. From the materials you need a dense foam, from it you need to cut the handle to size with a hacksaw. Along the length of the handle, a longitudinal hole should be burned out, where the whip will enter. You can achieve this even with a well-heated nail. The workpiece must be carefully cleaned with sandpaper, and then proceed with the installation of additional parts. You can use them as empty sewing spools. They give the necessary stability to a lightweight structure. An empty coil is sawn in half, its halves are glued to the handle. For greater strength, they are additionally reinforced with screws. In order for the filly’s winter fishing rod to be ready for use on ice, it should be painted with bright paint, soaked with drying oil. To fix the sharp parts of the hook or mormyshka, pieces of dense rubber or cork are glued to the lower surface of the handle.
Bezkivkovy winter fishing rod
The rod is a flexible whip 30 cm long with a line storage. The design is simple, light weight. From the tools you will need a drill, a drill for wood and a needle file. You also need to take a purchased winter balalaika fishing rod, a carbon whip, glue, a fishing line on a reel. First, a spool is taken, carefully sawn into 2 parts. After that, it is fixed on one side of the electric toothbrush. To make the resulting tackle easy to use, a small hole is made in the brush to fix the spool. A small whip is placed in the hole made in the brush on the other side. It is attached to the surface of the brush by cold welding. The fishing line is wound, the mormyshka is tied. In the form of a battery, a conventional finger-type battery is used for such a device. The principle of operation of a homemade nodding fishing rod is simple – when turned on, the motor starts to work, and the whip vibrates. The vibration that has arisen on it is transmitted to the mormyshka, providing a uniform range of motion. Do-it-yourself winter fishing rod: how to make tackle for lure, for a balancer for fishing for zander, perch: https://youtu.be/BVEaLXxGFe0
Self-cutting design
This is an automatic device that itself makes hooks when biting to spot fish. Self-hookers have many designs, but the principle of operation is the same. When the fish bites, there is a sharp change in the tension of the fishing line. This responds to the trigger mechanism, which activates the spring device. It lifts up the rod, pulling the line. Such a fishing rod allows you not to miss the moment of biting fish. First prepare the metal plate. A blank measuring 130 * 80 cm is cut out of a pre-prepared piece of sheet metal. This plate will become the base of the structure. On it you need to mark all the points for drilling and marks for bending it. 30 mm should be retreated from the smaller side and a straight line should be drawn so that it extends 3.5 cm from the sides. Then you need to retreat another 2 cm and draw a line 1 cm long. Near each corner make a mark for a hole for fixing. All excess is cut off with scissors for metal, and holes are made with an electric drill. After cutting, the edges are clamped, a semi-oval with holes is formed. The remaining sheet is folded in half. The result will be a part 13 cm long and 1 cm wide. Closer to the end of the resulting workpiece, holes are drilled at a distance of 4.5 cm from each of the edges. Then they take the wire and form a loop on one of the edges. The other end is bent at a 90 degree angle. Having measured 3 cm from the bent edge, it is necessary to form another loop. This element of equipment can be adjusted depending on the size of the base. If everything is prepared, you can start assembling the structure. The first blank is connected to the wire with nuts and bolts. At the end of the spring, you need to form a small hook. With it, there will be a clutch with a lever. The lever is attached to the base, the bolt is inserted into 2 holes so that the spring and the lever are fixed. The lever must be bonded to the spring to remain stationary.
Bringing a purchased winter fishing rod to mind – what problems can there be and ways to solve them
Many anglers experience poor reel performance. This part is built-in, non-removable, with a reel seat and the ability to install any suitable coil. Rods with a built-in reel can be used for jigging. Reels with reel seats are usually used for catching predators – these are pike, pike perch, large perch and burbot.
rubbing parts
Reels for winter fishing rods often do not have bearings. Plastic rubs against plastic, but this is normal only in the seats. You need to find an area where there should be no friction. For example, during rotation, the spool rubs against the body of the tackle, the cap of the tightening screw rubs against the inside of the spool. These points need to be addressed. With a sharp knife, abrasive or file, the rubbing parts should be filed, reducing the protruding diameter, which creates excess friction.
Lubricant
With its help, you can significantly improve the performance of any coil. It is necessary to lubricate all rubbing places. For example, the following parts can be lubricated in a refinished coil: After applying lubricant, the performance of the coil is greatly improved. It becomes not so noisy, more smooth. The clamping screw is easier to unscrew and unscrew. To make it work better as a clutch, you will need to install an intermediate washer. You can cut it out of lavsan. You can add a thin felt pad soaked in grease to smoothly adjust the friction. The lubricant must be resistant to frost, moisture, neutral with respect to the fishing line. It is better to choose silicone-based lubricants containing Teflon. In general, if you follow the step-by-step instructions on how to make a winter fishing rod, use high-quality materials, everything will work out. Tackle will be easy to use, will last a long time.
