The choice of a baitcasting reel for spinning: review, rating, parameters

The development of fishing equipment does not stand still, offering modern tackle and solutions. Spinning fishermen are a special caste of anglers and their tackle is special. Reels are one of the important parts of a spinning tackle. The most widespread are inertialess models. However, they are being replaced by another type – a multiplier reel. Cartoons are not so popular among spinners, but in some cases their use is more reasonable than the use of spinning reels.

Interesting to know! It is not recommended to put a multiplier on a regular spinning rod. On a blank for a multiplier reel, you need a large number of installed rings, a trigger for your finger, and a longer handle length. According to the cartoon principle, it is similar to the work of a winch.

Fishing winch [/ caption]

What is a baitcasting reel, what are its pros and cons compared to a spinning reel

The new is the well-forgotten old, says one of the proverbs. This is fully confirmed in the case of the mult, which is an improved inertial version of the coil. For a better understanding, consider the pros and cons of the bytecasting coil model.

Dignity

1. Increased power characteristics with small dimensions .
2. The center of gravity is as close as possible to the blank , which improves the overall balance. The inertialess grinder is distanced by the handle.
3. The line is close to the rod body due to the low spool position. Therefore, guides with short legs are used, reducing the weight of the equipment.
4. When casting the bait, the line is constantly in tension , the effect of a side wind (windage) is minimized.
5. Great sensitivity .
6. The throw distance does not depend on the thickness of the line and is performed with less effort.

Inherent and disadvantages

1. Expensive for the price compared to meat grinders of comparable quality.
2. Application skill is required to get close to the range of a spinning reel.
3. Casting spinning rods with a trigger are used. Top or spiral arrangement of pass rings.
4. Not applicable at low temperatures, grease thickens.
5. When the weight of the bait changes, it is necessary to adjust the settings of the braking system.
6. In most models, there is no adaptation for the right or left hand. Difficulties are experienced by “right-handers”.
7. Requires careful attitude: make sure that no sand, debris, salt water gets inside.
8. Ineffective with weightless baits.

Which reel is best for spinning: multiplier or spinning reel?

If you plan on purposeful fishing for large fish from a boat, then baitcasting equipment is preferable. However, the availability and versatility of “meat grinders” are the main advantages of the spinning coil models.

The device and principle of operation of the baitcasting reel

The watch became the prototype of this multiplier. In 1821, a master watchmaker, using the material at hand, made a comfortable fishing tackle for himself. The owner and his acquaintances liked the design so much that mass production by watchmaker’s works soon began. The main elements of a modern baitcasting reel are:

• frame;
• braking system;
• lever;
• spool;
• line laying mechanism;
• worm gear, gears.

The device of the cartoon [/ caption] The inertia is more complicated in the device. The principle of operation of the cartoon is similar to that of the winch. The handle drives the interlocking gears that rotate the spool. In turn, the worm gear starts to work, starting the line laying mechanism. A tuned brake system is of great importance in the correct operation of the reel. There are always two versions in the design.

1. Axial (mechanical for all types of coils) . Acts on the principle: the more tightened, the lower the drum rotation speed.
2. Magnetic or centrifugal .

The second type of system works in the initial stage of flight and regulates the number of spool revolutions.

It is important that the rotation of the reel while unwinding the line is comfortable for the flight of the bait. If the spool rpm is higher than the return line speed, beards are formed.

The axial brake comes into effect when the load touches the water, at this time the flight slows down, but the inertia of the drum rotation is still quite high. How the Baitcasting Reel Works – Video Beginner’s Guide: https://youtu.be/XcvS5zeS9M0

How to set up the baitcasting reel braking system

Beginners with multipliers often find it difficult to properly tune the baitcasting reel. But without the right set-up, fishing instead of an exciting activity will turn into a line-unraveling activity.

Mechanical brake settings

It is necessary to bring the spinning rod to a horizontal position (at least 1 meter from the ground). Pull the bait up, not reaching the tulip 5-10 cm. Fully apply the brake. By loosening the adjustment and slightly shaking the spinning rod, achieve the beginning of the downward movement of the load. The descent should be smooth, without jerking. At the moment of contact with the surface, the weakened drum should stop rotating.

On magnets

The adjustment moves the magnets away or closer to the metal spool. Set the regulator to the middle position. Disassembly of the coil body is not required.

Centrifugal option

Open the side cover and connect half of the available weights (pins): 2 out of 4; 3 out of 6; 4 of 8.
Braking weights [/ caption] In addition to choosing the number of working brakes, in some models, the distance or approximation of the surface (mirror), against which the elements rub due to centrifugal force, is carried out. There is external control. This expands the range of precise settings. There is a combined combination of magnets and pins. Experienced spinners completely release the mechanical brake and use their own thumb to slow down the rotation of the drum. Daiwa baitcasting reels have the patented Daiwa Magforce 3D braking system, which allows you to change the braking force in a split second by axial movement of the magnetic cup in the reel cheeks:
Daiwa Magforce 3D [/ caption]

How to secure and wind the line

The cord is fixed by tying various knots directly on the spool: “Arbor Knot”, self-tightening loop, power knot, “Grinner”, etc. After that, it is necessary to wind the fishing line.

It is important that during winding, the braid is stretched and laid down with some tension.

For this purpose, an ordinary bucket of water, a pencil and the help of a friend, thick books are used. There are also special winding machines. The option of securing and reeling is demonstrated in the video: https://youtu.be/OJLw2akzn_k How to wind a cord on a baitcasting reel and what to do if the cartoon twists the braid crookedly: https://youtu.be/0G7Ha9etZtg

Types of baitcasting reels

All models can be classified into three main categories:

2. Baitcasting cartoons for performing standard casts, suitable for fishing with jig lures and for twitching wobblers. They have a low profile and are called “soap dishes”. Models weight up to 200 grams. Used baits: 1-30 grams. Comfortably 3-30 grams.
3. Power baitcasting reels, – jerk models, as well as for fishing large jigs, spinners, wobblers. They are distinguished by rounded shapes. They are called “keg”. They are not effective for long-distance casts, they are used for fishing out large individuals. Such models weigh 200-300 grams, baits: 7-60 grams.
4. Trolling . For fishing in motion from boats, vertical fishing (sea). Powerful models, can be equipped with an electric motor and protection against the ingress of salt water. The presence of the meter of the descent of the fishing line. Depending on the class, the weight is 300-1500 grams. The baits are in the range: 40-1500 grams.

What to look for when choosing baitcasting reels

The main indicators and characteristics that you need to rely on in order to choose a baitcasting reel.

Power

Limits the maximum load on the tackle. If exceeded, breakdown is possible.

Brake system

The magnetic braking system is the most common. The amount of braking does not depend on the spool rotation speed. Therefore, it is well suited for long casts. Minus – the properties deteriorate in a side wind, due to the windage of the bait and fishing line, the speed of rotation of the drum can change. The centrifugal design affects the speed of flight. The more the spool spins, the tighter the pins are pressed against the mirror. Not suitable for long distance bait delivery. However, reliability, tuning accuracy and simplicity of design are popular with anglers.

Gear ratio

The winding speed is lower than that of the inertialess. This is due to design features. The fast baitcasting reel with a gear ratio of 7.3: 1 is similar in performance to the 5.2: 1 spinning reel in size 2500.

Line Layer Mechanism

Should wind the cord evenly. There is a switchable option. The reliability is higher for a constantly working mechanism, but at the same time the range is reduced. It is worth choosing multipliers with a ceramic hole / eye in the line guide rather than a metal one. This will allow you not to worry about the safety of both the cord and the line organizer – the braid cuts through the metal, but not the ceramics.

Number of bearings

For a smooth interaction of the components, at least 6 elements are recommended. How to choose a baitcasting reel for spinning, the principle of operation, features of use, pros and cons – video from recognized experts Shcherbakov brothers: https://youtu.be/Lt-qsMgUEuI

Tips for Beginner Spinning Players

How to start using baitcasting reels, which models you should pay attention to, the procedure for adjusting the braking systems and mastering the casting technique – about this and much more in the video: https://youtu.be/XcvS5zeS9M0

Cartoons care

Despite the simplicity and reliability of the design, periodic maintenance is required. Bearings, worm gear are subject to inspection. After purchase, it is recommended to remove factory grease. Rinse parts in kerosene, dry. Apply liquid synthetic oil to the bearings using a medical syringe with a needle. The grease is sold in specialized stores. Marine models are filled with a moisture resistant mixture.
Baitcasting reel mechanism [/ caption] After fishing, the reel is disassembled, the spool is removed. Parts are washed with clean fresh water and wiped dry. The rotating mechanisms are lubricated. Check the cleanliness of the mirror of the centrifugal mechanism, run it over the surface with a cotton swab, removing dust. Apply oil. Periodic maintenance is carried out after 3-4 fishing trips. A major overhaul is done once a year with complete disassembly. Baitcasting Reel Casting – Video Tutorial: https://youtu.be/RMPDqHUHVhM

TOP-10 popular models of baitcasting reels for spinning

A review of the best baitcasting reels for spinning of various functionality and price availability is offered.

Lucky John MAIKO 5.5 cm

This is a small model for winter fishing with long (for winter) spinning in a plumb line. Some experts classify it as inertial. The spool size is 5.5 cm, which can hold up to 80 m of line with a diameter of 0.25 mm. Installation for any hand is possible. The design has 4 ball and 1 roller bearing. There is no line laying mechanism. Adjustable friction brake with instant release function. The mechanical ratchet can be disengaged. Weight: 150 grams.

Falcon BY SeaKnight

The Chinese model of the baitcasting reel, according to customer reviews, is considered one of the best on Aliexpress. Stylish design and quality build. Coil with magnetic system. The setting allows you to fish with baits from 8 g. Ceramic wear-resistant line guide eye. 11 bearings provide a smooth ride, allowing for long and accurate casting. Gear ratio 7.2: 1. Weight: 190 grams.

Abu Garcia Revo Alt HS-L

Compact class for twitching fishing. Swedish model, targeting the domestic Japanese market. The body is made of aluminum alloy, which allowed to reduce the weight to 180 grams. The spool is wound with 100 meters of the declared line. Centrifugal braking of the IVCB-IV version allows fine tuning without removing the cover. “Mult” is equipped with 6 bearings. Used baits 7-20 gr.

Okuma Magda Pro 20 DLX

Line of trolling reels. The body is made of corrosion-resistant graphite. The brass main gear will pull the trophy specimens. Comfortable anatomical grip. Line guide based on endless screw. The model is equipped with a ratchet with mute. The mechanical line-off counter will show the distance to the bait (displayed in feet). An anti-reverse system is used in the design of the handle, which excludes reverse movement. The metal spool will hold 270 meters of monofilament with a diameter of 0.35 mm. Gear mechanism: 5.1: 1. Weight: 390 grams.

Tsurinoya XF 50L – Baitcasting reel for ultralight

Ultralight casting model. Lightweight perforated spool with bearing. Magnetic braking system. Quality red and black metal design and carbon additives. The load on the clutch is 4 kg. Lure weights: 1.5-15 grams. Model with backstop. Weight: 190 gr.

DAIWA CR80 – multiplier for beginners

Well suited for beginners “multi-drivers”. Small size fits comfortably in the hand. The sturdy carbon body is equipped with two covers and four ball bearings. Long and precise casting is provided by a magnetic drag. A 6.0: 1 ratio contributes to the persistence of fishing. Weight: 195 gr.

Shimano Calcutta ’12

Baitcasting reel Shimano Kolkata 12 is a classic sea keg. The increased diameter of the main drive gears, the location of the axle on protected bearings minimize the displacement of mechanisms in difficult fishing conditions. The centrifugal system is precisely tuned for weight values ​​of 5-40 grams. One turn of the handle spins 66 cm of line. The housing is protected by an EL coating to resist salt water. Weight: 255 grams.

Haibo Smart 2 151 MCS

Budget Chinese version. The set includes a spare spool, excellent in depth and line capacity. The coil body is an aluminum alloy with plastic side covers. Models in the line can be purchased under the preferred hand. Carbon handle and bearing knobs as an additional plus from the manufacturer. The ratio 6.5: 1 makes the mult into the category of “traction”. Weight: 193 grams.

JOHNCOO Baitcast

One of the easy models of cartoons. The body, handle and many of the internal parts are made of carbon. The characteristics allow using the Jonk Beitcast baitcasting reel for jerking, trolling and jig fishing. This is facilitated by 12 bearings and a gear ratio of 6.3: 1. Precise magnetic system in adjustment. Weight: 160 grams.

KastKing Brutus 4

An unusual external solution is striking – a closed body and a spool. What says about the marine focus. The line release button is placed in the back. Maximum load on the clutch: 5 kg. Additional advantages – the ability to rearrange the handle under the arm and installation on a classic spinning rod. Non-speed model with 4.0: 1 ratio. Suitable for beginner multi-drivers. Weight: 290 grams.
The full potential of the tackle can only be revealed in practice. Like any piece of equipment, there are pros and cons to reels. Which side outweighs is the personal preference of the fisherman.

Поделиться ссылкой: